Filament Splicer

Project cancelled, click here to read why
The idea for Filament Splicer was born about a month after our Ultimaker 3D Printer was build. As cool as 3D Printing is, printing in one color is boring.

Users of normal, single head FFF/FDM printers are stuck with single color unless they join filament pieces together to produce one multi-colored string. It is not very complicated but process is quite awkward and you will get fed up very quickly.

If you want to have proper, stable filament join you need to have right temperature on the tip of plastic when you connect pieces together. This is hard to achieve when you use some arbitrary heat source. You either underheat or overheat and burn the plastic. Using print head of your printer is best 'ad-hoc' solution but it leaves quite a mess on it, you cannot print when you splice and plastic which is in the head slowly gets burned while you take time to splice your string.

Then, of course there is issue with forming of the joint, carpet knife and fingers where our favorite tools for that job but it took quite a long time to form each joint.

We have had our share of failed prints due to broken joints / stuck filament and finally decided to create a device which will help to splice filament. Initial idea was to create fully automated unit: you place filament ends on copper block, close it, push the button and viola - you have your joint. That was the theory.... In practice this is impossible because PLA and ABS expand during heat-up and contract during cool down, this results in either no joint at all or bubble-filled mess.

Many headache filled days [Even best PLA is really nasty stuff when you breath it in for a while] later we dropped the idea and went for 'open' model with precisely manufactured grooves which help to quickly heat up, connect and form joints.

Thermal insulation was another challenge, we wanted to allow up to 260c temperature but nothing could properly insulate enclosure from hot copper block for prolonged period of time. Ceramic fiber thermal tape can take that heat but one needs a lot of it and then there is itching... Chinese tape is horrible and even best branded, made in USA [ThermoTec] tape is not flawless. We eventually gave up on ceramic fibre and went with PFTA [Teflon] plates. Since PFTA can be outright poisonous at high temperatures, we decided to use high quality - made in Europe material - this way we are sure that maximum temperature of 235c is well within safety limit.

Availability

Filament splicer can be pre-ordered via our campaign on Indiegogo, it is available as a DIY kit or fully assembled unit.

 

Assembled
Assembled
Kit
Kit

 

Open Source

Filament splicer blueprints are released under Creative Commons Attribution-NonCommercial 4.0 International License and can be downloaded from Thingiverse and Youmagine.

Tags: 
projects
filament splicer

42244 Comments

Anonymous

Michaelarepe (not verified)

on

Fri, 03/14/2025 - 08:01

2071 Темно-шоколадный https://sigmacolorshop.ru/shop/60/desc/maslo-vosk-sigma-terrasa

Раньше для подобных задач использовались средства на основе натуральных ингредиентов https://sigmacolorshop.ru/shop/108/desc/skipidar-zhivichnyj-terpentinnoe...
Сегодня производители предлагают ассортимент синтетических масел, которые сохраняют основные положительные качества, но при этом обходится заметно дешевле https://sigmacolorshop.ru/shop/62/desc/masljano-voskovaja-mastika-sigma-...

Древесина должна быть сухой и отшлифованной Нанесение выполняют послойно, давая высохнуть каждому слою Излишки продукта удаляют или распределяют по поверхности На все стороны изделия состав наносят равномерно Перед нанесением следующего слоя поднявшийся ворс шлифуют https://sigmacolorshop.ru/shop/67/desc/maslo-vosk-sigma-akva-par

2062 Темно-серый https://sigmacolorshop.ru/instrukcii

93% натуральных компонентов в составе https://sigmacolorshop.ru/sertifikaty

Масла Saicos для наружных работ https://sigmacolorshop.ru/shop/62/desc/masljano-voskovaja-mastika-sigma-...

Anonymous

Michaelarepe (not verified)

on

Fri, 03/14/2025 - 08:09

2063 Серый зелёно-белый https://sigmacolorshop.ru/

устойчивость к влажности, перепадам температуры, УФ-излучению; защита от естественного износа и вредного воздействия микроорганизмов; предотвращение гниения и распада https://sigmacolorshop.ru/shop/81/desc/ehmulsija-karnaubskogo-voska

Сертификация https://sigmacolorshop.ru/about

2059 Крапива https://sigmacolorshop.ru/shop/antiseptiki-i-otbelivateli-dlja-dereva

Шезлонг своими руками https://sigmacolorshop.ru/shop/71/desc/maslo-vosk-dlja-stoleshnic

На нашем сайте вы можете купить оригинальные масла для дерева Биофа от немецкого производителя https://sigmacolorshop.ru/photo/poly_i_lestnichnye_stupeni/3-2
Цена состава зависит от нескольких факторов:

Anonymous

Sandyarero (not verified)

on

Fri, 03/14/2025 - 09:21

Возможно, я ошибаюсь.
{it is necessary|important|necessary|required} {to know|understand|realize} that {the company|corporation|concern} {with which|where} {you|visitor|player} trade {values its reputation|maintains reputation|maintains reputation} {as much as {all|her} president values {his|her own} name or the name of the #file_links["C:\Users\Admin\Desktop\file\gsa+en+seomaster50k120325URLBB.txt",1,N].

Anonymous

Gwenovash (not verified)

on

Fri, 03/14/2025 - 11:21

Какие слова... супер, великолепная фраза
106. Repetto HA, Levi J.E., Braudo J.L. and other. for the treatment of acute pulmonary edema in parents , [url=https://forusemidetop.com/]furosemide use[/url] of 40 mg of furosemide can be slowly administered intravenously for 1-2 minutes.

Pages

Add your comment

More information about text formats

Plain text

  • No HTML tags allowed.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.